logo
blog
Home > blog > Company blog about Transformer Testing Equipment for Manufacturing and Quality Control
Events
Contact Us

Transformer Testing Equipment for Manufacturing and Quality Control

2026-11-18

Latest company news about Transformer Testing Equipment for Manufacturing and Quality Control
TECHNICAL BLOG  ·  TRANSFORMER TESTING

What Factory Testing Has to Prove

Every transformer needs to pass a series of tests before it leaves the factory. These tests produce important records, including voltage ratio, winding resistance, insulation resistance, power losses and oil breakdown voltage.

But why are these measurements necessary?

In simple terms, factory testing helps answer one important question: Was the transformer manufactured correctly, and can the manufacturer provide test records to prove it?

This is different from field testing. Field testing usually checks whether a transformer that has already been installed is still in good condition. Factory testing focuses on verifying the quality of the newly manufactured unit.

This difference also affects the equipment a factory needs.

A field engineer often needs portable instruments for testing at substations. A transformer factory, on the other hand, needs equipment that can perform repeatable measurements, support an efficient production process and keep test records for each transformer.

The same electrical characteristics may be measured in both situations, but the equipment configuration and testing requirements can be different.

Four Questions Quality Control Must Answer

Transformer manufacturing quality control generally focuses on four questions.

  • Does the transformer match its design? Tests such as turns ratio, vector group and winding resistance help identify incorrect connections, winding problems and manufacturing errors.
  • Can its insulation withstand the required voltage? Insulation resistance, dielectric and partial discharge tests help evaluate the condition of the insulation system.
  • Does it meet its performance commitments? No-load loss, load loss and impedance measurements help verify important performance values specified in the contract.
  • Is there a record for future comparison? Test reports and Frequency Response Analysis (FRA) results can provide a reference for future maintenance and condition assessment.

IEC 60076-1 distinguishes between routine tests, type tests and special tests. Routine tests are generally performed on individual transformers, while type and special tests have different purposes and application requirements.

The exact tests required for a particular transformer depend on the applicable standard edition, transformer design and customer contract. Manufacturers should confirm these requirements before defining acceptance criteria.

The Transformer Factory Testing Sequence

A transformer factory may perform several tests at different manufacturing stages. The following table shows common testing activities and the equipment that may be used.

StageWhat is measuredWhat the test helps identifyTypical XZH instrument
Incoming oilBreakdown voltage and moisture contentWet or contaminated insulating oilXHYY102M BDV tester, XHWS180 moisture analyzer
Winding assemblyDC resistance of each phase and tapBroken strands, loose connections and poor jointsXHZ1320A 20 A DC resistance tester
Ratio and connectionTurns ratio and vector group at different tap positionsIncorrect winding ratio or internal connectionsXHBB128B three-phase TTR tester
InsulationInsulation resistance, PI and DARMoisture, contamination and possible insulation deteriorationXHMR-15KVA 15 kV megohmmeter
Dielectric and PDApplied voltage, induced voltage and partial dischargeInsulation weaknesses that a resistance test may not detectPD detector with AC test set
Loss measurementNo-load loss, load loss and impedance voltageCore and winding performance deviationsXHTX1318 capacity and loss tester
FRA testingWinding frequency responsePossible winding deformation or movementXHBX1501 FRA analyzer
Oil conditionBDV, moisture, tan delta and dissolved gasOil degradation and possible internal problemsXHYY102M, XHWS180 and XHSP1700

The sequence matters.

For example, ratio and resistance checks can identify some manufacturing problems before the transformer is fully assembled. Finding these problems early can reduce the time and cost of rework.

Other tests, such as loss measurement and FRA, are performed at later stages when the transformer assembly is closer to its final condition.

Ratio and Vector Group: Checking the Winding Connections

A transformer turns ratio test checks whether the relationship between the primary and secondary windings matches the design.

The basic relationship is:

a = (U1) / (U2) = (N1) / (N2)

The ratio error can be calculated as:

Error(%) = (ameasured-anameplate) / (anameplate)×100

Here:

  • (U_1) and (U_2) are the primary and secondary voltages.
  • (N_1) and (N_2) are the number of turns in the two windings.
  • (a) is the transformer turns ratio.

In practical testing, a ratio tester applies a test voltage and measures the corresponding voltage relationship. It then compares the measured ratio with the expected value.

IEC 60076-1:2011 specifies a tolerance for the measured voltage ratio at the principal tapping. The permitted deviation is the lower of:

  • ±0.5% of the specified ratio; or
  • ± one tenth of the actual percentage impedance at the principal tapping.

For example, if the actual percentage impedance at the principal tapping is 4%, one tenth of that value is 0.4%. In this case, 0.4% is lower than 0.5% and therefore determines the applicable tolerance under this rule.

The ratio tolerance for other tap positions is specified separately. The applicable standard edition and customer contract should always be checked before using these values as acceptance criteria.

Two points are particularly important when selecting a ratio tester.

1. Test every required tap position.

A transformer may have several tap positions to adjust its output voltage. Checking only the principal tap may miss an incorrect connection at another position.

The XHBB128B three-phase turns ratio tester has a measurement range of 0.9–10000 and an accuracy of ±0.1%. It supports up to 99 tap positions.

This can be useful for factories manufacturing transformers with multiple or asymmetric tap arrangements.

2. Check the vector group, not just the ratio.

A transformer can have the correct turns ratio but still have an incorrect winding connection.

The vector group describes how the transformer windings are connected and how their phase relationships are arranged. This is important when transformers need to operate in parallel or connect to specific electrical systems.

The XHBB128B supports three-phase excitation and automatic vector group identification from 0 to 11.

A ratio test checks the winding ratio and connection relationship. It does not prove that the insulation can withstand the required voltage. That requires separate insulation and dielectric tests.

Winding Resistance: Checking the Quality of Electrical Connections

Winding resistance testing measures the electrical resistance of a transformer's windings.

Why does this matter?

A winding should have a reasonably consistent electrical connection throughout its conductive path. Problems such as broken strands, loose connections, poor solder joints, poor brazing or high-resistance tap contacts can affect the measured resistance.

These problems may increase losses or cause abnormal heating during operation.

However, winding resistance is affected by temperature. A warmer winding normally has a higher resistance than the same winding at a lower temperature.

This means that resistance readings taken at different temperatures cannot be compared directly. They should first be converted to the same reference temperature.

For copper windings:

R2 = R1×(235+T2) / (235+T1)

For aluminium windings:

R2 = R1×(225+T2) / (225+T1)

Where:

  • (R_1) is the measured resistance.
  • (R_2) is the resistance corrected to the reference temperature.
  • (T_1) is the temperature during measurement.
  • (T_2) is the reference temperature.

The constants 235 and 225 are conventional engineering values commonly used for copper and aluminium winding resistance correction. Other references use slightly different values, such as 234.5 for copper and 228 for aluminium. These values should not be treated as interchangeable without checking the applicable test procedure.

For consistent comparisons, particularly between factory and third-party laboratory reports, the calculation method, temperature reference and constants used should be recorded.

Two common mistakes can affect the result.

  • Measuring before the winding temperature and reading have stabilized. Large transformer windings can take time to reach a stable measurement condition. Taking a reading too early may produce inconsistent results.
  • Comparing phases without temperature correction. Temperature differences can affect resistance readings and may create an apparent imbalance.

The XHZ1320A 20 A DC resistance tester supports simultaneous three-phase measurement in Yn, Y and delta configurations. It also calculates the unbalance rate and provides a demagnetization function.

Simultaneous measurement can reduce testing time on a production line. Demagnetization is also useful because residual magnetism left in the transformer core may affect subsequent no-load measurements.

The appropriate test current depends on the winding resistance and the instrument's output capability. Factories should select a tester that covers the resistance range of their transformer product mix.

Any phase imbalance acceptance limit should be based on the applicable technical specification or customer requirement, rather than treated as a universal value.

Insulation Resistance, PI and DAR

Insulation resistance testing helps evaluate whether the insulation between electrical parts is in a suitable condition.

Moisture, contamination and insulation damage can reduce insulation resistance. This makes the test useful as an early check during transformer manufacturing.

A single resistance reading provides useful information, but readings taken over time can provide additional insight.

Two commonly used indicators are PI and DAR.

PI = (R(10 min)) / (R(1 min))
DAR = (R(60 s)) / (R(15 s))

PI stands for Polarization Index. It compares the insulation resistance after ten minutes with the reading after one minute.

DAR stands for Dielectric Absorption Ratio. It compares readings taken at 60 seconds and 15 seconds.

Why compare readings at different times?

When a test voltage is applied, insulation resistance may increase over time. The way it changes can provide information about the insulation condition. Moisture and contamination can affect this response.

Some specifications require a PI value above 2.0 for oil-immersed power transformers. However, this is not a universal acceptance requirement. The actual threshold must come from the applicable specification or customer requirement.

The XHMR-15KVA insulation resistance tester provides six test voltages from 500 V to 15 kV, a measurement range of 0.01 MΩ–50 TΩ, automatic PI and DAR calculation, and storage for up to 500 records.

When performing insulation resistance tests, operators should also consider temperature, humidity and surface contamination. A good insulation resistance result does not automatically mean that the transformer will pass a dielectric withstand test.

Dielectric Tests, Partial Discharge and Oil Breakdown Voltage

Insulation resistance testing is useful, but it cannot identify every insulation problem.

A transformer may show an acceptable insulation resistance value and still have weaknesses that become apparent under higher electrical stress.

This is why dielectric tests are important in transformer manufacturing.

Different dielectric tests check different parts of the insulation system:

  • Applied voltage testing checks the insulation between windings and other grounded parts.
  • Induced voltage testing applies voltage through the transformer to test the insulation between turns and other winding sections.
  • Impulse testing evaluates the transformer's ability to withstand transient overvoltage conditions. It is generally a type test rather than a routine test on every transformer.

Partial Discharge (PD) measurement can also be performed during relevant dielectric tests.

Partial discharge refers to a small electrical discharge that occurs in part of an insulation system without completely bridging the insulation between conductors. It may indicate problems such as voids or other local insulation defects.

The applicable PD limits and test conditions should follow IEC 60076-3 and the customer specification.

Oil breakdown voltage testing is different. It checks the electrical strength of the insulating oil rather than directly testing the transformer winding insulation.

IEC 60156 describes the oil breakdown voltage test method. A standard test cell uses a specified electrode arrangement, commonly with a 2.5 mm gap. Voltage is increased under controlled conditions until the oil breaks down electrically.

The XHYY102M 80 kV oil BDV tester supports GB/T 507, DL 429.9 and IEC 156 methods, with automatic testing and printed results.

For factories testing multiple oil samples, multi-cup versions such as the XHYY102L can help improve testing efficiency.

A high oil breakdown voltage is important, but it does not describe every aspect of oil condition. Moisture, acidity, dielectric loss and dissolved gases provide additional information.

Loss Measurement: Checking Transformer Performance

Transformer losses represent energy that is not transferred to the load but is instead lost inside the transformer.

These values matter because they affect operating efficiency and may be included in the manufacturer's contractual performance guarantees.

Two important measurements are no-load loss and load loss.

  • No-load loss mainly comes from the transformer core. It exists when the transformer is energized, even if the secondary side is not supplying a load.
  • Load loss mainly comes from the windings and other effects when the transformer carries current.

Impedance voltage is another important parameter used in transformer performance evaluation and specified in many transformer contracts.

IEC 60076-1:2011 Table 1 specifies a +10% tolerance for total losses. The tolerance for each measured component loss is +15%, provided that the total-loss tolerance is not exceeded.

These are positive-side acceptance tolerances, not symmetrical ±10% or ±15% limits. They also do not mean that a measuring instrument can have an accuracy of 10% or 15%. Instrument accuracy and measurement uncertainty must be considered separately.

The XHTX1318 capacity and loss tester measures capacity, no-load current, no-load loss, load loss and impedance voltage for transformers from 30 kVA to 31,500 kVA.

Its stated voltage and current accuracy is ±0.2%, while power accuracy is ±0.5% at power factors above 0.1. It can store up to 500 results and print test records on site.

The stated power accuracy must be considered together with its specified power-factor condition. Before selecting the instrument for a particular load-loss test, factories should confirm that the actual test power factor falls within the range covered by the accuracy specification. If it does not, the applicable accuracy at that operating condition needs to be confirmed.

For reliable results, factories should also control the test conditions. Waveform distortion, supply frequency, temperature and the relationship between the test values and the instrument's measurement ranges can all affect the results.

The standard's loss tolerances should not be treated as a substitute for evaluating the measurement system. Instrument accuracy, calibration, phase-angle effects and other sources of measurement uncertainty all matter when assessing whether a measured value is reliable.

Factories that also manufacture current transformers (CTs) and voltage transformers (PTs) may need additional testing equipment.

The XHTX206 CT/PT analyzer supports tests including excitation characteristics, ratio, burden and 10% error curves.

FRA: Creating a Reference for Future Transformer Checks

Frequency Response Analysis (FRA) is used to check the mechanical condition of transformer windings.

A simple way to understand FRA is to think of it as creating a fingerprint of the winding.

The instrument measures how the winding responds to electrical signals at different frequencies. The resulting curve represents the winding's frequency response.

If the winding moves or becomes deformed, its electrical characteristics may change. This can cause the measured curve to change as well.

However, an FRA result is most useful when it can be compared with another measurement.

In a factory, engineers can compare the responses of different phases on the same transformer. This is called a horizontal comparison.

After transportation or a later electrical event, a new measurement can be compared with the original factory result. This is called a longitudinal comparison.

IEC 60076-18 describes the FRA measurement technique.

The XHBX1501 winding deformation tester covers a frequency range of 100 Hz to 2 MHz and records amplitude and phase information.

For meaningful comparisons, the measurement setup should remain consistent. This includes the test lead arrangement, grounding point and transformer tap position.

Without a suitable factory baseline, a later FRA measurement may be difficult to interpret because there is no original reference for comparison.

Building a Test Bench for Different Factory Types

Not every transformer factory needs the same equipment configuration.

The right selection depends on the transformer types being manufactured, the required tests, production volume and customer specifications.

The following table provides a starting point for planning a factory test bench.

Factory typeEssential equipment to considerAdditional equipment
Distribution transformer assemblyTTR, DC resistance tester, insulation resistance tester, oil BDV testerLoss and capacity tester, FRA analyzer
Power transformer manufacturingTTR, DC resistance tester, insulation resistance tester, loss tester, oil BDV and moisture testingFRA analyzer, PD measurement, DGA
Instrument transformer manufacturingCT/PT analyzer, insulation resistance testerDC resistance tester, PD equipment for applicable HV units
Repair and rewinding workshopTTR, DC resistance tester, insulation resistance tester, oil BDV testerFRA analyzer, loss tester, PD and DGA equipment

This is a general selection reference, not a fixed equipment list. Actual requirements should be determined by the factory's product range and testing responsibilities.

Two procurement considerations can help avoid unnecessary investment.

First, select equipment according to the actual measurement ranges and accuracy requirements of your products. The highest voltage rating or largest range on a product brochure is not automatically the best choice.

Second, consider testing efficiency as well as measurement accuracy. Features such as automatic tap testing, simultaneous three-phase resistance measurement and multi-sample oil testing can reduce repetitive work on a production line.

Throughput, Traceability and Calibration

A factory test is only useful when the result can be repeated, recorded and checked later.

Four practices are particularly important.

  • Connect every test result to the transformer serial number. Records should also identify the relevant phase, tap position and test conditions.
  • Keep original measurement records. FRA fingerprints and resistance values can provide useful references for future field testing.
  • Calibrate instruments regularly. Calibration should follow an appropriate schedule and be considered after equipment repair.
  • Control test conditions. Temperature, humidity and other environmental factors can affect certain measurements. Record these conditions when they are relevant to the test.

These practices help manufacturers maintain consistent quality control and provide more reliable test documentation to customers.

Five Mistakes That Can Cause Rework

Some testing mistakes produce readings that appear normal but are not reliable.

  • Testing only the principal tap instead of checking all required tap positions.
  • Recording winding resistance before the measurement has stabilized.
  • Comparing insulation resistance readings taken under different temperature conditions.
  • Using different FRA lead arrangements for the factory baseline and later field measurements.
  • Treating a good oil BDV result as proof that the oil is in good condition in every respect.

These mistakes can lead to unnecessary retesting, production delays and difficulties during customer acceptance.

A reliable testing process is not only about choosing the right instrument. It also depends on using the instrument correctly and keeping consistent records.

Questions Buyers Ask Before Building a Test Bench

Which transformer tests are routine tests and which are type tests?

IEC 60076-1 distinguishes routine tests, type tests and special tests.

Routine tests are generally performed on individual transformers. Type tests are used to verify the design, while special tests are agreed between the manufacturer and customer.

The exact test requirements depend on the applicable standard edition, transformer design and contract. Manufacturers should confirm these details before preparing their factory test procedures.

Can one instrument perform both ratio and resistance tests?

Yes. Some combined transformer testing systems can perform both turns ratio and DC winding resistance tests.

For a distribution transformer production line, a combined system may reduce equipment handling and the need to reconnect test leads between separate instruments.

However, separate instruments may still be more suitable for factories with a wider range of transformer sizes and different testing requirements.

What accuracy is needed for transformer loss measurement?

The required accuracy depends on the measurement values, test conditions and contractual tolerance being checked.

The instrument should have sufficient accuracy under the actual test conditions to distinguish whether the measured result is within the required limit. Voltage and current measurement accuracy, power factor and phase-angle effects can all affect the final power measurement.

Factories should consider the complete measurement system and its uncertainty rather than selecting equipment based on one accuracy figure alone.

Is FRA necessary for distribution transformers?

FRA is not automatically required as a routine test for every distribution transformer.

It may be useful when a factory or customer wants a reference measurement before transportation, particularly for units where transportation damage would be costly.

For larger power transformers, maintaining a factory FRA baseline can be especially valuable because it provides a reference for future condition assessment.

KEY TAKEAWAYS

Transformer factory testing is a sequence of checks that helps manufacturers verify product quality before delivery.

Each test has a different purpose:

Ratio testing checks winding ratios and connections.

DC resistance testing helps identify winding and connection problems.

Insulation and dielectric tests evaluate the insulation system.

Loss measurement checks important performance values.

FRA provides a reference for evaluating possible winding changes.

Oil testing helps assess the condition of the insulating oil.

The right equipment configuration depends on transformer type, production volume, testing requirements and customer specifications.

Conclusion

Building a reliable transformer test bench is not simply a matter of purchasing as many instruments as possible. It is about matching each testing stage with suitable equipment and creating a process that produces consistent, traceable results.

For transformer manufacturers, the right combination of testing instruments can help identify problems earlier, reduce repeated testing and improve factory quality control.

Building or upgrading a transformer factory test bench?

Send us your transformer types, voltage classes and annual production volume. XZH TEST can help map your testing requirements to suitable instruments and confirm the relevant measurement ranges, accuracy and testing functions.

Talk to XZH TEST →

Send your inquiry directly to us