logo
Home > Products >
AC DC Hipot Tester
>
Shielded Cable VLF Hi-Pot Tester XHDP Series Withstand Voltage Testing Equipment

Shielded Cable VLF Hi-Pot Tester XHDP Series Withstand Voltage Testing Equipment

Product Details:
Place of Origin: China
Brand Name: XZH Test
Certification: CE/ISO
Model Number: XHDP Series
Detail Information
Place of Origin:
China
Brand Name:
XZH Test
Certification:
CE/ISO
Model Number:
XHDP Series
Model NO.:
C
Test Mode:
Saved Test
Usage:
Network Cable Tester, HDMI Cable Tester, Audio Cable Tester, Coaxial Cable Tester, Digital Cable Tester
Test Region:
Forming Cable
Cable Type:
Shielded
Power:
Electricity
Customized:
Customized
Color:
Orange
Transport Package:
Wooden Box With Foam Inside
Specification:
350mm*280mm*170mm
Trademark:
XZH TEST
Origin:
China Xi′ An
HS Code:
8543201000
Supply Ability:
100 Pieces /Year
Customization:
Available
After-sales Service:
Warranty Certificate
Warranty:
1 Year
Highlight:

High Light

Highlight:

VLF Hi-Pot tester for shielded cable

,

AC DC withstand voltage tester

,

Hi-Pot tester with VLF technology

Trading Information
Minimum Order Quantity:
1unit
Packaging Details:
wooden box
Delivery Time:
5-8work days
Payment Terms:
T/T
Supply Ability:
3000unit/year
Product Description
Shielded Cable Hi-Pot

Shielded Cable VLF Hi-Pot Tester XHDP Series Withstand Voltage Testing Equipment

A VLF hi-pot set for shielded and forming cable, with high side sampling, built-in output protection and a printer that puts the test record on paper at the end of the run.

30 - 80 kV peak
Shielded and forming cable
Protection below 20 ms
Built-in printer

Overview

The XHDP series VLF hi-pot tester applies a 0.1 Hz AC withstand voltage to shielded cable and forming cable, where the capacitance of the insulation makes a 50 Hz test impractical. Boost, step-down, measurement and protection are controlled automatically, and the output waveform is shown on the display while the test runs. The integrated printer produces a record of the test at the end of the run.

XHDP Series Tester Display

Testing shielded cable

On a shielded cable the insulation sits between the conductor and the metallic shield, so the test voltage is applied to the conductor and the shield is earthed. One phase is tested at a time; the capacitance to check against the load limit is that of a single phase to earth, not the whole three-phase circuit. The same arrangement applies to forming cable, where the insulation is tested before the cable goes into service.

Model range

ModelRated voltage / current0.1 Hz0.05 Hz0.02 HzSupply fuseController / booster
XHDP-3030 kV / 20 mA (peak)≤ 1.1 uF≤ 2.2 uF≤ 5.5 uF5 A4 kg / 25 kg
XHDP-5050 kV / 30 mA (peak)≤ 1.1 uF≤ 2.2 uF≤ 5.5 uF15 A4 kg / 50 kg
XHDP-6060 kV / 30 mA (peak)≤ 1.1 uF≤ 2.2 uF≤ 5.5 uF20 A4 kg / 55 kg
XHDP-8080 kV / 30 mA (peak)≤ 1.1 uF≤ 2.2 uF≤ 5.5 uF20 A4 kg / 50 kg + 45 kg

Measurement and protection

High side samplingCurrent, voltage and waveform are taken directly from the high voltage side, so the record shows the values at the specimen.
Over-voltage protectionThe output is shut down in less than 20 ms when it exceeds the set voltage limit, before the fault can damage the booster.
Dual current protectionHigh side and low side over-current protection act on the set values, with a response time below 20 ms.
Built-in protective resistorThe high voltage output has an internal protective resistor, so no external resistor has to be added to the test circuit.

Records and operation

The controller uses a large display to show the output waveform, stores each test automatically and prints a report through the integrated printer. The interface can be switched between Chinese and English, and the set runs from 220 V +/- 5 %, 50 Hz, or from a portable generator with a stable output above 3 kW.

Where the set is used

  • After-laying and after-jointing withstand tests on shielded XLPE cable.
  • Forming cable tests before the cable is put into service.
  • Repair and maintenance work where a printed record has to go into the test file.
  • Workshops that test several cable classes and need one controller with the matching booster.

Frequently asked questions

How is a shielded cable connected for the test?

The test voltage is applied to the conductor and the metallic shield is earthed. One phase is tested at a time, so the capacitance to check against the load limit is the single-phase capacitance to earth.

Can the set be used for forming cable?

Yes. The XHDP series is used for forming cable as well as for shielded cable, with the same 0.1 Hz withstand method and the same 30-80 kV range.

What is the protection response time?

Over-voltage and over-current protection act in less than 20 ms. The high voltage output also has a built-in protective resistor, so no external resistor is needed.

Does it print a test record?

Yes. Each test is stored automatically and printed through the integrated printer, so the voltage, current and outcome are on paper without manual transcription.

Test list check

Send the cable type, the voltage class and the capacitance per phase, and we will confirm the rating and whether one booster covers the whole list.

Ratings & Review

Overall Rating

5.0
Based on 50 reviews for this supplier

Rating Snapshot

The following is the distribution of all ratings
5 stars
100%
4 stars
0%
3 stars
0%
2 stars
0%
1 stars
0%

All Reviews

N
Nikolaos Papadopoulos
Greece Jul 7.2026
Η συσκευή XHDP‑80M δοκιμής υπερβολικά χαμηλής συχνότητας έχει εξαιρετική απόδοση για την ομάδα διανομής μας. Πραγματοποιήσαμε δοκιμές αντοχής σε υπόγεια καλώδια 20kV στον υποσταθμό Κερατέας κοντά στην Αθήνα. Η λειτουργία με οθόνη αφής είναι εύκολη, η προστασία ενεργοποιείται γρήγορα και οι μετρήσεις παραμένουν ακριβείς ακόμα στη μεσογειακή ζέστη. Ανθεκτική κατασκευή για εργασίες πεδίου, μειώνει σημαντικά τον χρόνο προετοιμασίας των δοκιμών. Συνιστάται ανεπιφύλακτα για τα συνεργεία ηλεκτρικής ενέργειας στην Ελλάδα.